搜索资源列表
FPGA从cy7c68013读取数据实现
- FPGA将从CY7C68013A读到的数据写入SRAM-FPGA
Mars-SP3-U_SCH.rar
- 一块XC3S400 FPGA电路板的原理图，板子上有CY7C68013A作为USB接口,A XC3S400 FPGA circuit board schematics, board have CY7C68013A as USB interface
USB_FPGA_FOR_SRAM-control
- 此程序完成PC上位机通过USB与板上SRAM进行的数据传输交换，有CY7C68013A的SALVE_FIFO的完整固件及FPGA的SRAM驱动程序，并已调通可用了。-This process is complete PC via USB and PC-board SRAM for data transfer exchange, complete with CY7C68013A of SALVE_FIFO of SRAM FPGA firmware and drivers, and has bee
42pcb
- 该工程是一个FPGA的开发板 主要包括了FPGA芯片:EP3C25Q240C8 FPGA的配置芯片采用：EPCS16 USB芯片：CY7C68013A USB的FLASH采用：24LC64 AD芯片：AD9238 电源部分：LMS1117-3.3两块分别对USB、模拟部分和FPGA供电；LMS1117-1.2为FPGA核心电压；LMS1117-2.5为 IO口及PLL供电 9盏LED，4个开关 主要完成的一个功能是高速模拟信号的采集，以及上位机传输
T2_USB_IN
- CY7C68013A提供的端口FIFO的读写操作，与普通FIFO读写操作方式一样。CY7C68013A为每个端口提供了“空”标志、“满”标志和“ 可编程级”标志。FPGA检测这些信号，用于控制读写的过程-CY7C68013A available port FIFO read and write operations, and general FIFO read and write operations the same way. CY7C68013A for each port provide
usb_fpga_1_2_latest.tar
- USB2.0的FPGA内核，使其可以通过FPGA控制CY公司出品的CY7C68013USB微控制器，对USB设备进行读写操作。-• Xilinx Spartan-3 XC3S400 FPGA • High-Speed (480 MBit/s) USB interface via Mini-USB connector (B-type) • Cypress CY7C68013A/14A EZ-USB-Microcontroller • 60 G
ucecho
- Working example for Java application to connect to USB device CY7C68013A using an FPGA. FPGA automaticcaly writes data to be fetched from USB device. Java application runs speed test (upto 30 MB/s) and checks quality of data.
bmp
- Quick BMP-Test for CY7C68013A-USb device. Ready to run program for FPGA.
VHDLvom22.08.2008
- Very simple program for FPGA to write bulk data on CY7C68013A USB controller.
CY3686-Board-Design-Files
- 是驱动CY7C68013A的USB接口系统,可以应用于FPGA、DSP的开发-Driver the CY7C68013A' s USB interface system can be applied to the development of FPGA, DSP
FA161-SCH
- 联华众科FPGA开发板FA161核心器件为 Altera Cyclone系列FPGA EP1C6，FA161板载有SDRAM，SRAM，FLASH方便制作各种应用，开发板所带资料中包括了上位机与开发板USB通信，上位机与开发板以太网通信，上位机与开发板串口通信例程。FA161板载有USB 1.1，USB 2.0(CY7C68013A)接口，以太网接口(RTL8019AS)。FA161上可以进行HDL程序开发，可以进行nios ii程序开发，可以结合MATLAB制作DSP Builder应用。FA
AsyFIFO
- cy7c68013a芯片的slaveFIFO传输例程，利用异步传输可以实现数据读写，包含芯片固件代码和fpga发送数据的代码。
USB_fpga
- FPGA与USB PHY芯片Cy7c68013A通信的程序，Verilog语言-FPGA and USB PHY chip Cy7c68013A communication procedures, Verilog language
verilog_src
- 基于FPGA的cy7c68013a读写控制程序-cy7c68013a control program
SLAVE-FIFO-16BITS
- CY7C68013a的slavefifo的固件源代码，keil编写，以及使用FPGA向EP6端点写数据的verilog源代码，没有错误，可以编译成功!-CY7C68013a of slavefifo firmware source code, keil prepared using FPGA and write data to the endpoint EP6 verilog source code, no errors, you can compile successfully!
TestProject
- 用fpga + usb ,fpga 用ep3c10e144 , usb 用釙68013日. 使用nios dma 傳輸數據至cy7c68013 , 經usb 到電腦-it use altera cyclone iii ep3c10e144 and cypress cy7c68013a to pc using nios dma to transmit data to pc via cy7c68013
CY7C68013A_board_test
- 该资料基于FPGA实现USB2.0的高速传输，即CY7C68013A芯片的数据传输，包括FPGA与上位机之间数据的相互传输，CY7C68013A的传输速率最高可达480M/S。-The FPGA-based high-speed data transmission USB2.0, that CY7C68013A chip data transmission, including the mutual transmission of data between the FPGA and the ho
Asy_slavefifo_rdwr(141027)
- FPGA 控制CY7C68013A芯片的收发程序，调试通过，最高速度18M-CY7C68013A chip transceiver FPGA control procedures, debugging through, the maximum speed of 18M
FPGA_USB_Communication
- 本软件利用USB控制芯片cy7c68013A实现了USB通讯。压缩文件包括在fpga里面编程的vhdl软件-This software uses the USB control chip cy7c68013A to achieve the USB communication. The compressed file include programming in FPGA VHDL software
CCD_Array
- Interface TCD1209DG with Altera FPGA and transfer image data to PC via USB using USB FX2 Slave FIFO mode, Only FPGA code included.